DSP SINE WAVE INVERTER WITH SOLAR CONTROL

WORKING PRINCIPLE

modified sine wave control using pic16f876a

MODIFIED SINE WAVE INVERTER CONTROL USING PIC16F876A

 

Control and Monitoring of an inverter during operation has being the major problem which locally made inverters Manufacturer encounters which has led to low demand for locally built Inverters due to sudden break down as a result of overcharging of the batteries, overuse of the battery below the low battery spec. and high voltage during charging. most of the Inverter schematic claimed or used by Local Inverter Manufacturer downloaded from the internet are for tutorial purpose not not for commercial there are tendencies for failure therefore it is time for us to start developing things of our own...
proudly NIGERIA......
The featuring M.C.U is the Microchip PIC16F876A
FEATURES INCLUDES:

INVERTER PROTECTION : LOW-BATTERY SHUTDOWN
                                             : OVER LOAD SHUTDOWN INPUT
                                             : OUTPUT SHORT CIRCUIT SHUT-DOWN
                                             : HIGH TEMPERATURE SHUT-DOWN
                                             : LOW-BATTERY : BEEP START AT 11 V
                                             :LOW BATTERY INVERTER SHUT DOWN AT 10.5 V
                                             :10 SEC DELAY BEFORE CHARGING
                                             : AUTOMATIC VOLTAGE REGULATOR
                                               [INPUT: 160 V - 250 V]
                                               [OUTPUT: 211 V - 232 V]

                                             : HIGH VOLTAGE PROTECTION
                     
INVERTER  MONITOR  : 16*2 LCD DISPLAY
                                         : ERROR LED
                                         : BUZZER

The  pic16f876a is programmed with picbasic pro software and the board components can easily arranged and tested by any electronic personnel.

Below are the schematics:

FIG1: PROTEUS SIMULATION1

FIG2: PROTEUS SIMULATION 2

FIG3: PROTEUS SIMULATION 3

FIG4: PROTEUS SIMULATION 4

FIG5: SCHEMATIC DIAGRAM

FIG6: CHARGING SIMULATION

FIG7: INPUT VOLTAGE SIMULATION

FOR TUTORIAL AND HELP OR PURCHASE OF THE PANEL BOARD {EMPTY OR COMPLETE}
CONTACTS: 08138110639 OR 07018399701
EMAIL: JVERTECHELECT@GMAIL.COM,
YOU CAN MAIL ME FOR THE HEX FILE AND THE CIRCUIT DIAGRAM

modified sine wave for beginners at low cost

SIMPLE WAY OF DOING INVERTER

Hello, here is a simple way to make a home/office modified sine wave inverter that can power various appliance such as bulbs, TV. A modified sine wave inverter gives an output which is intermediate between the square wave and pure sine wave.

For a modified sine wave inverter, we need two inverted square signal to switch the mosfets to generate these signals we make use of ‘cd4047’ multi-vibrator i.c. we use it in a stable mode which gives a buffered output so there is no need for impedance matching. In a stable mode it generate square wave of exactly 50% duty cycle at its pin 10 and its inverted signal on pin 11. It also generates frequency double to that of pin 10 at pin 13.

                                                                WORKING PRINCIPLE

We gave a pwm signal to the pair of MOSFETS connected in a push pull configuration. When the first side of the mosfet  say[side A] is turned on by high input, then the second side of the mosfet say [side B] turns off at that time because on its input we had an inverted signal with some delay. The delay is used so that one of the mosfets get time to turn off before second one turns on. In this mode, the current flows from source to mosfet side A. when the first signal goes low then the second signal becomes high and side B of the mosfet turns on resulting in current flowing from source thus we get a high voltage output at the transformer primary. A 10k ohms resistor from gate to source is important because when the input signal goes to zero, the mosfets may not completely turn off because of the capacitance between gate and source so this resistance makes sure that the signal is fully grounded. The threshold voltage to turn on mosfet is approximately 4v. we are driving mosfets with 12v signal so that mosfets is completely turned on otherwise it will lead to power dissipation….

Below is a simple schematic diagram that can help in your design   

 

FIG1 : CD4047 OSCILLATOR CIRCUIT DIAGRAM

 Part list include: 

• 104 cap
• 5k variable resistor
• cd4047
• Tip41c
• 8v zener diode
• 2 * 220ohms resistor
• 1kohms resistor
• irfp 250n
• 470ohms resistor * 6
• 10k resistor * 2
• 12v big inverter transforme {center tap} 

watch out for more circuit diagram especially oscillator using sg3524 ic.

for more info, you can contact me on 08138110639 or 07018399701 or mail @ jvertectelect@gmail.com

PURE SINE WAVE INVERTER WITH LED AND LCD

PURE SINE WAVE INVERTER WITH LED AND LCD

The inverter PCB is easy to assemble by following the label of the components to be inserted. The choice of the voltage to be used to power the inverter ranging from 12v to 96v depends on kva you are designing. for any setup,  a 12v relay is to be used. 
The featuring M.C.U are the Microchip PIC16F72A  and  PIC16F876A
FEATURES OF THE ABOVE SCHEMATIC ARE STATED BELOW :

INVERTER PROTECTION : LOW-BATTERY SHUTDOWN
                                              : OVER LOAD SHUTDOWN INPUT
                                              : O/P SHORT CCT SHUT-DOWN INPUT
                                              : HIGH TEMPERATURE SHUT-DOWN INPUT
                                              : LOW-BATTERY : BEEP START AT 11 V
                                              :INVERTER SHUT DOWN AT 10.5 V
                                              :10 SEC DELAY BEFORE CHARGING
                                              : AUTOMATIC VOLTAGE REGULATOR
                                               [INPUT: 180 V - 240 V]
                                               [OUTPUT: 211 V - 232 V]
                      
INVERTER  MONITOR  : 16*2 LCD DISPLAY
                                           : LED INDICATORS
                                           : ERROR LED
                                           : BUZZ

 

 Fig 1: COMPLETE SINE WAVE INVERTER MOTHERBOARD

 

Fig 2: COUPLING OF MODIFIED SINE WAVE INVERTER

                                           Fig 3: MODIFIED SINE WAVE INVERTER BOARD
                                      

FOR ENQUIRIES CALL 08138110639 0R 0701839970